CAM-EFI
  • Home
  • Shop
    • Throttle Bodies
    • Inlet Manifolds
    • ECU / Looms / Injector harness / Function Looms
    • Injectors/Extensions
    • Fittings / Fuel Lines
    • Accessories
    • Trigger wheels and Kits
    • Fuel Regulators
    • Throttle Position Sensors
    • KMS Engine kits
    • Levers and Springs
    • Air Horns
    • Throttle Linkage/ Fuel Rail
    • Connectors / Super Seal / Pin Sets
    • Van Kronenburg Car Parts
    • Miscellaneous / DCOE Adaptors / *****LOOK****** Manifold Ends ****LOOK****
  • Bespoke
  • Gallery
  • About
  • Short Circuit Gearing
  • Contact
All prices exclude VAT

Potentiometer mounting kit

£5.40

Potentiometer mounting kit

Shop

KMS Speed sensor -> CAN converter 4-channel

£215.00
he KMS Speed sensor to CAN converter converts the signals of four speed inputs (hall or inductive) onto the CAN bus. This enables the four speed inputs to be monitered on the CAN display or in the KMS motormanagement software. Using the KMS Speed sensor to CAN converter also enables the use of traction control and speed limiters on the KMS MD35 ECU.

Included within the KMS Speed sensor to CAN converter package is a CAN communication hub and a manual.
Shop

KMS UEGO CAN controller set

£334.80
The KMS UEGO CAN controller is a state of the art wide band lambda controller designed to work with a Bosch LSU 4.9 wide band lambda sensor. It measures the oxygen level in the exhaust at a rate of 2000 samples/sec and converts it to a lambda value.

Connection of the KMS UEGO CAN controller is very straightforward due to the prefabricated wiring loom. The wiring loom contains the connections for the lambda sensor, external ground and analog and CAN communication outputs with which the controller can communicate.

Included within the KMS UEGO CAN controller package is a wiring loom, CAN communication hub, contra connector, welding nut, Bosch LSU 4.9 wide band lambda sensor and manual. ​
Shop

KMS Electronic Throttle Controller

£608.00
The KMS Electronic Throttle Control (ETC) is a powerful and reliable system for the control of electronic throttle valves in various applications. It enables users to control electronic throttle valves, stand-alone or in cooperation with an engine control unit. The system uses a powerful PID algorithm to ensure that the electronic throttle valve will be reacting, under all circumstances, within a few milliseconds.

It allows users to get the full potential from the electronic throttle valve with functions like RPM limiter, Anti Lag (ALS) control, launch control, pedal response, throttle blip and many more. The KMS ETC module has an extensive automatic calibration process which enables a reliable use of the system within a few minutes.

Included within the KMS ETC package is a wiring loom main connector, communication cable and wiring diagram.
Shop

KMS MAP-sensor 100kPa

£95.00
KMS pressure sensors suitable for measuring the pressure in the suitable range.
Features:
• Water resistant, compact and robust design
• 4 and 6 mm hose connection on MAP sensor
• Dash -3AN connection on oil/fuel pressure sensor
• Sensor cell resistant to fuels, oils and other liquids
• 0-5v output signal (pre-calibrated for KMS ECU’s)
• Measuring speed <7 ms
• EMC protection up to 100V
• Internal temperature compensation
• Supplied with contra connector, manual and calibration values.
Shop

KMS Pressure-sensor 1010 kPa M10x1

£85.00
The KMS pressure sensor 1010kPa is suitable for measuring pressures up to 10 bar, mostly used for oil pressure. The sensor is featured with M10x1 thread.
Shop

KMS G-force sensor 3-axis +/- 2G

£210.00
KMS sensor for measuring G-forces in three directions. The output signals can be connected to the KMS Management ECU’s for datalogging purposes. Featuring:

Compact and robust design
Water resistant
Available in ±2G and ±6G
3 axis (x,y,z)
0-5V linear output
Supplied including contra connectors, manual and calibration values
Shop

KMS G-force sensor 3-axis +/- 6G

£210.00
MS sensor for measuring G-forces in three directions. The output signals can be connected to the KMS Management ECU’s for datalogging purposes. Featuring:

Compact and robust design
Water resistant
Available in ±2G and ±6G
3 axis (x,y,z)
0-5V linear output
Supplied including contra connectors, manual and calibration values
Shop

Crank-sensor universal (inductive)

£35.00

Crank-sensor universal (inductive)

Shop

Throttle position sensor (3pin Ford Style)

£43.00

Throttle position sensor (3pin Ford Style)

Shop

Throttle position sensor (6pin Bosch)

£130.80

Throttle position sensor (6pin Bosch)

Shop

Air-temperature sensor M12x1,5

£12.75

Air-temperature sensor M12x1,5

Shop
1 2 3
Proudly powered by Weebly
  • Home
  • Shop
    • Throttle Bodies
    • Inlet Manifolds
    • ECU / Looms / Injector harness / Function Looms
    • Injectors/Extensions
    • Fittings / Fuel Lines
    • Accessories
    • Trigger wheels and Kits
    • Fuel Regulators
    • Throttle Position Sensors
    • KMS Engine kits
    • Levers and Springs
    • Air Horns
    • Throttle Linkage/ Fuel Rail
    • Connectors / Super Seal / Pin Sets
    • Van Kronenburg Car Parts
    • Miscellaneous / DCOE Adaptors / *****LOOK****** Manifold Ends ****LOOK****
  • Bespoke
  • Gallery
  • About
  • Short Circuit Gearing
  • Contact